Products

Connector for mounting sandwich panels in cold stores.

Produced by SWAL since 2008.

Reduces thermal bridge and condensation effect.

It is designed to work with SWAL screws.

.

LAX should be used with a screw with an EPDM washer ∅ 16 mm made of galvanized carbon steel or stainless steel.

FROST-FREE

• Installation time: 30 seconds

• Material: modified polyamide

• RAL colours: 7044, 9002, 9003, 9005, 9006, 9007, 9010 - other to individual order

• Working temperature: -40 to +85°C

• Design load-bearing capacity: 1,97 kN.

• Breaking force: 4,50 kN.

Fastening side lap & trim in fibreglass or vinyl panels

Recommendation:Fastener for fixing trapezoid and corrugated polycarbonate panels, vinyl, PCV, etc.

Material: ALF screw: stainless steel A2.; EPDM sleeve, Stainless steel washer: S16, S19, A16, A19 with EPDM

Cover caps provide the best protection for the screw head

Plastic caps for 8 and 10 mm hexagonal heads

Application: masking screw heads, additional protection against corrosion

Material: polyethylene

Color according to RAL

An ideal solution for freezer rooms and cold stores where fire resistance is required

stainless steel panels in production rooms, e.g. intended for fish or meat cutting.

It can be used as a kit with a 19 mm EPDM washer or a 22 mm galvanised steel washer.

Sheet metal cladding pre-drilling with a drill bit with diameter 11 mm is required.

.

• Material: modified polyamide with UV protection add-on

• RAL colours: 7044, 9002, 9003, 9005, 9006, 9007, 9010 - other to individual

For agro plates and halls in the case of the environment.

WELRO is equipment for the installation of agro-type wall and roof sandwich panels with plastic cladding, plastic-coated sheets or stainless steel sheets and the installation of sandwich panels in a C4 - C5M water environment. It can be installed with a screw with a 19 mm thick EPDM washer or a 22 mm thick galvanized steel washer.

No pre-drilling required.

Material: modifiable polyamide with appropriate UV Standard

Colors according to RAL: 7044, 9002, 9003, 9005, 9006, 9007, 9010 - other to individual

It can be installed with a screw with a 19 mm thick EPDM washer or a 22 mm thick galvanized steel washer.

For suspended ceilings in cold stores

The maximum panel length between the shapes is specified in the technical specifications provided by the manufacturer of the panels used for given project.

The T-Shape can be fitted can be made using a fork joint with an M8 threaded rod or an elastic sling.

.

Material: high quality aluminium alloy

Painting: oven baked polyester powder paint

Provides perfect fixation thanks to the use of two components.

.

Depending on the type of surface, the gray element made of high-quality nylon automatically adapts to the optimal holding method (expanding, folding, rolling), ensuring the best fastening.

.

Red expansion wings support expansion and additionally protect the gray element. The stud screws in easily and tightens precisely at the end, eliminating the risk of over-tightening. The specially formed edge of the pin prevents it from falling into the hole.

.

Application: installation of sandwich panels on silicate bricks, foamed concrete, perforated bricks

Material: poliamid    

.

.

                 Light concrete                        Sandwich panel

                  The pin expands in four directions

Hole saw for drilling a hole in the slab for LAX

Fastening to steel sections up to 28 mm

Calculated load capacity - 2.5kN.

Hangers for trapezoidal sheet metal

Through hole Φ 13 or M8 flange nut.

Calculated load capacity - 2.5kN.

The maximum recommended load also depends on the load-bearing capacity of the trapezoidal sheet.

Before installation, contact the roof constructor to obtain information about the load-bearing capacity of the trapezoidal sheet.

For suspended ceilings

Snap hook with security

EYE-EYE